public class ImageInputStreamAdapter extends FilterInputStream
in
Constructor and Description |
---|
ImageInputStreamAdapter(ImageInputStream iis) |
Modifier and Type | Method and Description |
---|---|
int |
available()
Returns an estimate of the number of bytes that can be read (or
skipped over) from this input stream without blocking by the next
caller of a method for this input stream.
|
void |
close()
Closes this input stream and releases any system resources
associated with the stream.
|
void |
mark(int readlimit)
Marks the current position in this input stream.
|
boolean |
markSupported()
Tests if this input stream supports the
mark
and reset methods. |
int |
read()
Reads the next byte of data from this input stream.
|
int |
read(byte[] b,
int off,
int len)
Reads up to
len bytes of data from this input stream
into an array of bytes. |
void |
reset()
Repositions this stream to the position at the time the
mark method was last called on this input stream. |
long |
skip(long n) |
read
public ImageInputStreamAdapter(ImageInputStream iis)
public int read() throws IOException
int
in the range
0
to 255
. If no byte is available
because the end of the stream has been reached, the value
-1
is returned. This method blocks until input data
is available, the end of the stream is detected, or an exception
is thrown.
This method
simply performs in.read()
and returns the result.
read
in class FilterInputStream
-1
if the end of the
stream is reached.IOException
- if an I/O error occurs.FilterInputStream.in
public int read(byte[] b, int off, int len) throws IOException
len
bytes of data from this input stream
into an array of bytes. If len
is not zero, the method
blocks until some input is available; otherwise, no
bytes are read and 0
is returned.
This method simply performs in.read(b, off, len)
and returns the result.
read
in class FilterInputStream
b
- the buffer into which the data is read.off
- the start offset in the destination array b
len
- the maximum number of bytes read.-1
if there is no more data because the end of
the stream has been reached.NullPointerException
- If b
is null
.IndexOutOfBoundsException
- If off
is negative,
len
is negative, or len
is greater than
b.length - off
IOException
- if an I/O error occurs.FilterInputStream.in
public long skip(long n) throws IOException
This method simply performs in.skip(n)
.
skip
in class FilterInputStream
IOException
public int available() throws IOException
This method returns the result of in
.available().
available
in class FilterInputStream
IOException
- if an I/O error occurs.public void close() throws IOException
in.close()
.close
in interface Closeable
close
in interface AutoCloseable
close
in class FilterInputStream
IOException
- if an I/O error occurs.FilterInputStream.in
public void mark(int readlimit)
reset
method repositions this stream at
the last marked position so that subsequent reads re-read the same bytes.
The readlimit
argument tells this input stream to
allow that many bytes to be read before the mark position gets
invalidated.
This method simply performs in.mark(readlimit)
.
mark
in class FilterInputStream
readlimit
- the maximum limit of bytes that can be read before
the mark position becomes invalid.FilterInputStream.in
,
FilterInputStream.reset()
public void reset() throws IOException
mark
method was last called on this input stream.
This method
simply performs in.reset()
.
Stream marks are intended to be used in situations where you need to read ahead a little to see what's in the stream. Often this is most easily done by invoking some general parser. If the stream is of the type handled by the parse, it just chugs along happily. If the stream is not of that type, the parser should toss an exception when it fails. If this happens within readlimit bytes, it allows the outer code to reset the stream and try another parser.
reset
in class FilterInputStream
IOException
- if the stream has not been marked or if the
mark has been invalidated.FilterInputStream.in
,
FilterInputStream.mark(int)
public boolean markSupported()
mark
and reset
methods.
This method
simply performs in.markSupported()
.markSupported
in class FilterInputStream
true
if this stream type supports the
mark
and reset
method;
false
otherwise.FilterInputStream.in
,
InputStream.mark(int)
,
InputStream.reset()
Copyright © 1999–2019 ViaOA. All rights reserved.